Analyzing the Consequences of Procedure Parameters on Multi Responses
DOI:
https://doi.org/10.61841/jkhzr828Keywords:
WEDM system parameters WASPAS-Taguchi S/N ratio evaluation,, esponses & optimizationAbstract
On this paper, improvement of WEDM system parameters was focused on. The enhancement changed into cleared out machining of AMMNCs test of carbon Nano tube supported al 5056. Experimentations were finished as with regards to Taguchi design of examinations for different mixes of system parameters like heartbeat on-schedule, beat off-time, water pressure, Height present day to check the reactions like disposal value, floor harshness, kerf width and apparatus wear. A blended WAPAS-Taguchi S/N proportion Analysis is utilized to explore the impacts of procedure parameters on Responses and to recognize the most satisfying parameter setting in EDM of AMMNC. From the ANOVA, it's demonstrated that beat on time is most fundamental enter parameter followed by method for top present day, beat off time and water pressure influencing the reactions. It is resolved that higher outcomes are acquired from WASPAS-S/N proportion investigation; subsequently it is right to recognize the greatest parameters assessment through the blending of techniques.
Downloads
References
1. P. Venkataramaiah and Dileep (2011). AHP-DENG’S similarity based optimization of WEDM process parameters of Al/SiCp Composite. Journal of Materials Science and Technology, vol. 6, no. 1, pp. 1–14.
2. Kohzoh (2013). Study of EDM cutting of single crystal silicon carbide. Science Direct Precision Engineering, vol. 38, pp. 92– 99.
3. M. Ibrahem, L. H. Ling (2012). Improve WEDM performance at different machining parameters. IFAC,
pp. 105–110.
4. H. C. Dong WonKim (2014). Electrode wear estimation model for EDM drilling. Robotics and Computer-Integrated Manufacturing, vol. 36, pp. 70–75.
5. S. Rajesh, K. Ramji (2010). Optimization of machining parameters for cutting AMMC’s on wire cut EDM. International Journal of Engineering Trends and Technology, vol. 23, no. 2.
6. R., Maurya, N., Singh, P., & Gupta, S. Optimization of process parameters in electric discharge machining process.
7. Cao, Y., Huang, L., Li. Y., Jermsittiparsert, K., Ahmadi-Nezamabad, H., & Nojavan, S. 2020. “Optimal Scheduling of Electric Vehicles Aggregator under Market Price Uncertainty Using Robust Optimization Technique.” International Journal of Electrical Power & Energy Systems 117: 105628.
8. Yu, D., Wang, Y., Liu, H., Jermsittiparsert, K., & Razmjooy, N. 2019. “System Identification of PEM Fuel Cells Using an Improved Elman Neural Network and a New Hybrid Optimization Algorithm.” Energy Reports 5: 1365-1374.
9. Tian, M., Ebadi, A., Jermsittiparsert, K., Kadyrov, M., Ponomarev, A., Javanshir, N., & Nojavan, S. 2019. “Risk-Based Stochastic Scheduling of Energy Hub System in the Presence of Heating Network and Thermal Energy Management.” Applied Thermal Engineering 159: 113825.
10. Yu, D., Wnag, J., Li, D., Jermsittiparsert, K., & Nojavan, S. 2019. “Risk-Averse Stochastic Operation of a Power System Integrated with Hydrogen Storage System and Wind Generation in the Presence of
Demand Response Program.” International Journal of Hydrogen Energy (In press), DOI: 10.1016/j.ijhydene.2019.09.222.
11. Jabarullah, N., Jermsittiparsert, K., Melnikov, P., Maseleno, A., Hosseinian, A., & Vessally, E. 2019. “Methods for the Direct Synthesis of Thioesters from Aldehydes: A Focus Review.” Journal of Sulfur Chemistry (In press), DOI: 10.1080/17415993.2019.1658764.
12. Jiao, Y., Jermsittiparsert, K., Krasnopevtsev, A., Yousif, Q., & Salmani, M. 2019. “Interaction of Thermal Cycling and Electric Current on Reliability of Solder Joints in Different Solder Balls.” Materials Research Express 6 (10): 106302.
13. Yu, D., Ebadi, A., Jermsittiparsert, K., Jabarullah, N., Vasiljeva, M., & Nojavan, S. 2019. “Risk- constrained Stochastic Optimization of a Concentrating Solar Power Plant.” IEEE Transactions on Sustainable Energy (In press), DOI: 10.1109/TSTE.2019.2927735.
14. Jermsittiparsert, K., Sriyakul, T., Sutduean, J., & Singsa, A. 2019. “Determinants of Supply Chain Employees Safety Behaviours.” Journal of Computational and Theoretical Nanoscience 16 (7): 2959- 2966.
15. Sriyakul, T., Singsa, A., Sutduean, J., & Jermsittiparsert, K. 2019. “Effect of Cultural Traits, Leadership Styles and Commitment to Change on Supply Chain Operational Excellence.” Journal of Computational and Theoretical Nanoscience 16 (7): 2967-2974.
16. Sutduean, J., Singsa, A., Sriyakul, T., & Jermsittiparsert, K. 2019. “Supply Chain Integration, Enterprise Resource Planning, and Organizational Performance: The Enterprise Resource Planning Implementation Approach.” Journal of Computational and Theoretical Nanoscience 16 (7): 2975-2981.
17. Singsa, A., Sriyakul, T., Sutduean, J., & Jermsittiparsert, K. 2019. “Willingness of Supply Chain Employees to Support Disability Management at Workplace: A Case of Indonesian Supply Chain Companies.” Journal of Computational and Theoretical Nanoscience 16 (7): 2982-2989.
18. Jermsittiparsert, K. & Chankoson, T. 2019. “Behavior of Tourism Industry under the Situation of Environmental Threats and Carbon Emission: Time Series Analysis from Thailand.” International Journal of Energy Economics and Policy 9 (6): 366-372.
19. Romprasert, S. & Jermsittiparsert, K. 2019. “Energy Risk Management and Cost of Economic Production Biodiesel Project.” International Journal of Energy Economics and Policy 9 (6): 349-357.
20. Kasayanond, A., Umam, R., & Jermsittiparsert, K. 2019. “Environmental Sustainability and its Growth in Malaysia by Elaborating the Green Economy and Environmental Efficiency.” International Journal of Energy Economics and Policy 9 (5): 465-473.
21. Jermsittiparsert, K, Sriyakul, T., & Rodoonsong, S. 2013. “Power(lessness) of the State in the Globalization Era: Empirical Proposals on Determination of Domestic Paddy Price in Thailand.” Asian Social Science 9 (17): 218-225.
22. Jermsittiparsert, K, Sriyakul, T., & Pamornmast, C. 2014. “Minimum Wage and Country’s Economic Competitiveness: An Empirical Discourse Analysis.” The Social Sciences 9 (4): 244-250.
23. Jermsittiparsert, K., Pamornmast, C., & Sriyakul, T. 2014. “An Empirical Discourse Analysis on Correlations between Exchange Rate and Industrial Product Export.” International Business Management 8 (5): 295-300.
24. Jermsittiparsert, K., Sriyakul, T., Pamornmast, C., Rodboonsong, S., Boonprong, W., Sangperm, N., Pakvichai, V., Vipaporn, T., & Maneechote, K. 2016. “A Comparative Study of the Administration of
Primary Education between the Provincial Administration Organisation and the Office of the Basic Education Commission in Thailand.” The Social Sciences 11 (21): 5104-5110.
25. Jermsittiparsert, K., Trimek, J., & Vivatthanaporn, A. 2015. “Fear of Crime among People in Muang- Ake, Lak-Hok, Muang, Pathumthani.” The Social Sciences 10 (1): 24-30.
26. Jermsittiparsert, K. & Akahat, N. 2016. “Fear of Crime among Students of Kalasin Rajabhat University.” Research Journal of Applied Sciences 11 (2): 54-61.
27. P. V. Ramaiah (2016). Application of Taguchi, Fuzzy-Grey Relational Analysis for Process Parameters Optimization of WEDM on Inconel-825. Indian Journal of Science and Technology, vol. 8, no. 35.
28. N and Dalgarnob. K. W. (2014). Effect of wire EDM cutting parameters for evaluating of Additive Manufacturing Hybrid Metal Material. Proc. of 2nd International Materials, Industrial, and Manufacturing Engineering Conference, 4-6, Indonesia, pp. 532 – 537.
29. Arunkumar. L, Raghunath. B. K. Electro Discharge Machining Characteristics of Mg/SiCPMetal matrix Composites by Powder Metallurgy Techniques. International Journal of Engineering and Technology.
30. Kanlayasiri. K, Boonmung. S (2006). Effects of wire - EDM machining variables on surface roughness of newly developed DC 53 die steel: Design of experiments and regression model. Journal of Materials Processing Technology, 192–193, pp. 459– 464.
31. B. Puri, B. Bhattacharyya (2004). An analysis and optimization of the geometrical inaccuracy due to wire lag phenomenon in WEDM,” International Journal of Machine Tools & Manufacture, vol. 43, 2003, pp. 151–159.
32. Dr. G. Krishnaiah (2016). Optimization of process parameters using AHP and VIKOR when turning aisi 1040 steel with coated tools. International Journal of Mechanical Engineering and Technology, vol. 8, Iss. 1, pp. 241–248.
33. P. Shandilya, P. K. Jain, N. K. Jain (2011). Wire electric discharge of metal matrix composite. Damm International scientific book, pp. 383-400.
34. Saravanakumar, A., Santarao, K., & Nandini, G. Influence of alumina nano powder mixed dielectric fluid in electric spark machining of aisi d3 steel. Carbon (c), 2, 2–3.
35. R. K. Bhuyan, and B. C. Routara (2016). Optimization the machining parameters by using VIKOR and Entropy Weight method during EDM process of Al–18%SiCp Metal matrix composite. Decision Science Letters, vol. 5, pp. 269–282.
36. Bhattacharyya, B. (2014). Analysis of traveling wire electrochemical discharge machining of Hylam based composites by Taguchi method. International Journal of Research in Engineering & Technology, 2(2), 223–236.
Downloads
Published
Issue
Section
License
This work is licensed under a Creative Commons Attribution 4.0 International License.
You are free to:
- Share — copy and redistribute the material in any medium or format for any purpose, even commercially.
- Adapt — remix, transform, and build upon the material for any purpose, even commercially.
- The licensor cannot revoke these freedoms as long as you follow the license terms.
Under the following terms:
- Attribution — You must give appropriate credit , provide a link to the license, and indicate if changes were made . You may do so in any reasonable manner, but not in any way that suggests the licensor endorses you or your use.
- No additional restrictions — You may not apply legal terms or technological measures that legally restrict others from doing anything the license permits.
Notices:
You do not have to comply with the license for elements of the material in the public domain or where your use is permitted by an applicable exception or limitation .
No warranties are given. The license may not give you all of the permissions necessary for your intended use. For example, other rights such as publicity, privacy, or moral rights may limit how you use the material.
